درایو موتور آسانسور نمایندگی اشنایدر فرانسه مدل ATV71LD17N4Z

سری محصول

Altivar Lift

نوع کاربرد محصول

Variable speed drive

نام کوتاه محصول

ATV71

کاربرد موتور محصول

Asynchronous motors
Synchronous motors

کاربرد خاص محصول

Lift

نوع اسمبل

With heat sink

نمایش متغیر ها

With integrated 7-segment display terminal

EMC دارای فیلتر

Integrated

تعداد فاز شبکه

3 phases

[Us] نرخ ولتاژ تغذیه

380…480 V – 15…10 %

محدوده ولتاژ تغذیه

323…528 V

فرکانس تغذیه

50…60 Hz – 5…5 %

توان موتور بر حسب kW

7.5 kW, 3 phases at 380…480 V

توان موتور بر حسب  hp

10 hp, 3 phases at 380…480 V

جریان خط تغذیه

27 A for 380 V 3 phases 7.5 kW / 10 hp
22.2 A for 480 V 3 phases 7.5 kW / 10 hp

توان ظاهری

17.8 kVA at 380 V 3 phases 7.5 kW / 10 hp

Isc

22 kA for 3 phases

خروجی جریان اسمی

17.6 A at 4 kHz 380 V 3 phases 7.5 kW / 10 hp
14 A at 4 kHz 460 V 3 phases 7.5 kW / 10 hp

ماکزیمم جریان گذرا

23.9 A for 2 s 3 phases / 7.5 kW / 10 hp

فرکانس خروجی درایو سرعت

0…599 Hz

حداقل مقاومت ترمز

12 Ohm

فرکانس اسمی سوییچینگ

8 kHz

فرکانس سوییچینگ

1…16 kHz adjustable

نرخ سرعت

1…100 for asynchronous motor in open-loop mode, without speed feedback
1…50 for synchronous motor in open-loop mode, without speed feedback
1…1000 for asynchronous motor in closed-loop mode with encoder feedback

دقت تغییر سرعت

+/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn
+/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn

دقت گشتاور

+/- 5 % in closed-loop mode with encoder feedback
+/- 15 % in open-loop mode, without speed feedback

اضافه گشتاور گذرا

170 %, +/- 10 % for 60 s
220 %, +/- 10 % for 2 s

گشتاور ترمز

30 % without braking resistor
<= 150 % with braking or hoist resistor

مشخصات موتور های آسنکرون قابل کنترل

Flux vector control without sensor, ENA (energy Adaptation) system
Flux vector control with sensor, standard
Voltage/frequency ratio – Energy Saving, quadratic U/f
Flux vector control without sensor, standard
Voltage/frequency ratio, 5 points
Flux vector control without sensor, 2 points
Voltage/frequency ratio, 2 points

مشخصات موتور آسنکرون

Vector control with sensor, standard
Vector control without sensor, standard

حلقه رگولاتور

Adjustable PI regulator

جبران لغزش موتور

Not available in voltage/frequency ratio (2 or 5 points)
Automatic whatever the load
Adjustable
Suppressable

سیگنالینگ محلی

1 LED (red) for drive voltage

ولتاژ خروجی

<= power supply voltage

ایزولاسیون

Electrical between power and control

نوع کابل برای اتصال خارجی

Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC
With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC

اتصال الکتریکی

Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR)
Terminal, clamping capacity: 6 mm², AWG 8 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

نیروی گشتاور

3 N.m, 26.5 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR)

تغذیه

Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protection
Internal supply: 24 V DC (21…27 V), <200 A, protection type: overload and short-circuit protection

تعداد ورودی آنالوگ

2

نوع ورودی آنالوگ

AI2 software-configurable voltage: 0…10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits
AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
AI2 software-configurable current: 0…20 mA, impedance: 242 Ohm, resolution 11 bits

چرخه نمونه بردای

2 ms +/- 0.5 ms (LI6)if configured as logic input – discrete input(s)
2 ms +/- 0.5 ms (LI1…LI5) – discrete input(s)
2 ms +/- 0.5 ms (AI1-/Al1+) – analog input(s)
2 ms +/- 0.5 ms (Al2) – analog input(s)

پاسخ زمانی

R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s)
AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
<= 100 ms in STO (Safe Torque Off)

دقت

+/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
+/- 0.6 % (AI2) for a temperature variation 60 °C
+/- 1 % (AO1) for a temperature variation 60 °C

خطای خطی

+/- 0.15 % of maximum value (AI1-/Al1+, AI2)
+/- 0.2 % (AO1)

تعداد خروجی آنالوگ

1

نوع خروجی آنالوگ

AO1 software-configurable voltage: 0…10 V DC, impedance: 470 Ohm, resolution 10 bits
AO1 software-configurable current: 0…20 mA, impedance: 500 Ohm, resolution 10 bits
AO1 software-configurable logic output 10 V 20 A

تعداد خروجی های مجزا

2

نوع خروجی مجزا

Configurable relay logic: (R1A, R1B, R1C) NO/NC – 100000 cycles
Configurable relay logic: (R2A, R2B) NO – 100000 cycles

مینیمم جریان سوییچینگ

3 mA at 24 V DC for configurable relay logic

ماکزیمم جریان سوییچینگ

5 A at 250 V AC on resistive load – cos phi = 1 – L/R = 0 ms (R1, R2)
5 A at 30 V DC on resistive load – cos phi = 1 – L/R = 0 ms (R1, R2)
2 A at 250 V AC on inductive load – cos phi = 0.4 – L/R = 7 ms (R1, R2)
2 A at 30 V DC on inductive load – cos phi = 0.4 – L/R = 7 ms (R1, R2)

تعداد ورودی مجزا

7

نوع ورودی های مجزا

Programmable (LI1…LI5)24 V DC, with level 1 PLC – 3500 Ohm
Switch-configurable (LI6)24 V DC, with level 1 PLC – 3500 Ohm
Switch-configurable PTC probe (LI6) – 0…6 probes – 1500 Ohm
Safety input (PWR)24 V DC – 1500 Ohm

ورودی های منطقی

Positive logic (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1)
Negative logic (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1)
Positive logic (LI1…LI5), < 5 V (state 0), > 11 V (state 1)
Negative logic (LI1…LI5), > 16 V (state 0), < 10 V (state 1)
Positive logic (PWR), < 2 V (state 0), > 17 V (state 1)

شتاب مثبت و منفی رمپ

Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Linear adjustable separately from 0.01 to 9000 s
S, U or customized

نوع محافظت

Overheating protection: drive
Thermal protection: drive
Short-circuit between motor phases: drive
Input phase breaks: drive
Overcurrent between output phases and earth: drive
Overvoltages on the DC bus: drive
Break on the control circuit: drive
Against exceeding limit speed: drive
Line supply undervoltage: drive
Line supply overvoltage: drive
Against input phase loss: drive
Thermal protection: motor
Motor phase break: motor
Power removal: motor

dielectric strength

3535 V DC between earth and power terminals
5092 V DC between control and power terminals

مقاومت ایزولاسیون

> 1 mOhm 500 V DC for 1 minute to earth

وضوح فرکانس

Display unit: 0.1 Hz
Analog input: 0.024/50 Hz

پورت پروتکل ارتباطی

CANopen
Modbus

نوع کانکتور

1 RJ45 (on front face) for Modbus
1 RJ45 (on terminal) for Modbus
Male SUB-D 9 on RJ45 for CANopen

اینترفیس فیزیکی

2-wire RS 485 for Modbus

فریم انتقال

RTU for Modbus

نرخ انتقال

9600 bps, 19200 bps for Modbus on front face
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen

فرمت داده

8 bits, 1 stop, even parity for Modbus on front face
8 bits, odd even or no configurable parity for Modbus on terminal

نوع پلاریزاسیون (قطبش)

No impedance for Modbus

تعداد آدرس ها

1…247 for Modbus
1…127 for CANopen

 مد دسترسی

Slave CANopen

ویژگی های کنترل

Communication card for Modbus TCP
Communication card for Fipio
Communication card for Modbus/Uni-Telway
Communication card for Modbus Plus
Communication card for Ethernet/IP
Communication card for DeviceNet
Communication card for Profibus DP
Communication card for Profibus DP V1
Communication card for Interbus-S
Communication card for CC-Link
Interface card for encoder
I/O extension card
Controller inside programmable card
Overhead crane card

موقعیت کاری

Vertical +/- 10 degree

استاندارد الکترو مغناطیسی مطابقتی

Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
1.2/50 µs – 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11

درجه آلودگی

2 conforming to EN/IEC 61800-5-1

IP درجه محافظت

IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1
IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529
IP21 conforming to EN/IEC 61800-5-1
IP21 conforming to EN/IEC 60529
IP41 on upper part conforming to EN/IEC 61800-5-1
IP41 on upper part conforming to EN/IEC 60529
IP54 on lower part conforming to EN/IEC 61800-5-1
IP54 on lower part conforming to EN/IEC 60529

مقاومت متغیر

1.5 mm peak to peak (f= 3…13 Hz) conforming to EN/IEC 60068-2-6
1 gn (f= 13…200 Hz) conforming to EN/IEC 60068-2-6

شوک مقاومتی

15 gn for 11 ms conforming to EN/IEC 60068-2-27

سطح نویز

55.6 dB conforming to 86/188/EEC

نرخ رطوبت کاری دستگاه

5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3

دمای محیط کاری

-10…50 °C (without derating)

مقاومت دمایی درایو

-25…70 °C

ارتفاع کاری

<= 1000 m without derating
1000…3000 m with current derating 1 % per 100 m

استاندارد ها

EN 55011 class A group 2
EN 61800-3 environments 2 category C3
IEC 60721-3-3 class 3C1
EN 61800-3 environments 1 category C3
EN/IEC 61800-5-1
IEC 60721-3-3 class 3S2
UL Type 1
EN/IEC 61800-3

تاییدیه های محصول

C-Tick
CSA
NOM 117
UL
GOST

تاییدیه ها

CE